Forum

3 Tips for RF PCB Layout January 08, 2021 5:18 AM

By : wisepowder

3 Tips for RF PCB Layout

Because the radio frequency (RF) circuit is a distributed parameter circuit, skin effect and coupling effect are prone to occur in the actual work of the circuit, so in the actual PCB design, it will be found that the interference radiation in the circuit is difficult to control, Such as: mutual interference between digital circuit and analog circuit, noise interference of power supply, interference caused by unreasonable ground wire, etc. Because of this, how to weigh the pros and cons in the PCB design process to find a suitable compromise, to reduce these interferences as much as possible, and even to avoid the interference of some circuits, is the key to the success or failure of the RF PCB design. From the perspective of PCB LAYOUT, this article provides some processing skills, which are of great use to improving the anti-interference ability of radio frequency circuits.To get more news about Cavity PCB, you can visit pcbmake official website.

1.RF layout

What we discussed here is the layout of the components of the multilayer board. The key to the layout of components is to fix the components on the RF path. By adjusting its direction, the length of the RF path is minimized, and the input is far away from the output, and the high-power circuit and the low-power circuit are separated as far as possible. The signal is far away from high-speed digital signals and RF signals.

1.1 One-line layout

The components of the RF main signal are arranged in a straight line as much as possible, as shown in Figure 1. However, due to the limitation of PCB board and cavity space, it cannot be laid out in a straight shape in many cases. At this time, L-shaped layout can be used. It’d be better not to use U-shaped layout (as shown in Figure 2). When it is unavoidable, it’d be better to increase the distance between input and output to at least 1.5cm. In addition, when using an L-shaped or U-shaped layout, the turning point should not turn as soon as it enters the interface, as shown on the left in Figure 3, but after a slight straight line, as shown on the right in Figure The feed inductance of the bias circuit is placed perpendicular to the RF channel, as shown in Figure 6, mainly to avoid mutual inductance between inductive devices. In order to use the space reasonably, the devices can be arranged in a 45-degree direction to make the RF line as short as possible, as shown in Figure 7. 2.RF Routing

The overall requirements for wiring are: RF signal traces are short and straight, reduce line abrupt changes, drill fewer holes, and do not intersect with other signal lines, and add as many ground vias as possible around the RF signal line.


Re: 3 Tips for RF PCB Layout January 08, 2021 6:09 PM

By : Robin


Hi there, beautiful weblog  with great informational content. This is a really interesting and informative post. Ross Levinsohn


Re: 3 Tips for RF PCB Layout January 08, 2021 6:09 PM

By : Robin


Have you already setup a fan page on Facebook ?,::”: Ross Levinsohn


Re: 3 Tips for RF PCB Layout January 08, 2021 6:09 PM

By : Robin


Along with every little thing that appears to be building inside this area, your opinions are generally very stimulating. On the other hand, I beg your pardon, because I can not subscribe to your entire idea, all be it exhilarating none the less. It would seem to me that your commentary are not totally rationalized and in fact you are your self not fully convinced of the argument. In any event I did take pleasure in reading through it. Ross Levinsohn profile


Re: 3 Tips for RF PCB Layout January 08, 2021 6:09 PM

By : Robin


You ought to indulge in a tournament for starters of the most useful blogs on the internet. Let me suggest this site! Ross Levinsohn named Maven CEO


Re: 3 Tips for RF PCB Layout January 27, 2021 2:06 AM

By : Robin


Hello! I recently wish to offer a massive thumbs up to the great information you have here with this post. We are returning to your blog for much more soon. FOODS THAT CLEANSE THE LIVER


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


As I web site possessor I believe the content matter here is rattling magnificent , appreciate it for your hard work. You should keep it up forever! Best of luck. GLD Partners donates technology


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


Hello, you used to write fantastic articles, but the last several posts have been kinda lackluster… I miss your great articles. Past several posts are just a little out of track! Daniel Gordon Forbes Business Council


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


To use the no cost Worlds Best graphic responses: Duplicate the HTML code from below the graphic picture and paste the code in your blog Daniel Gordon GLD Partners


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


The thing i like about your blog is that you always post direct to the point info.:,*`, GLD Partners info


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


Wow! This can be one particular of the most useful blogs We have ever arrive across on this subject. Actually Magnificent. I’m also a specialist in this topic therefore I can understand your hard work. Daniel Gordon coursehero


Re: 3 Tips for RF PCB Layout January 29, 2021 10:12 AM

By : Robin


diamond engagement rings will be always be the best stuff. it has great style and it is priceless~ Ross Levinsohn


Re: 3 Tips for RF PCB Layout January 30, 2021 2:23 AM

By : Robin


Thanks , I’ve recently been searching for information about this topic for a while and yours is the greatest I’ve discovered so far. However, what in regards to the conclusion? Are you positive concerning the supply? New Maven CEO


To post a comment please register or sign in